Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Repair for Myers Park Homeowners
Water gets into masonry long before a homeowner notices anything wrong inside. By the time a stain shows on the firebox or a chunk of brick lands on the hearth, the mortar behind it has usually been failing for a couple of seasons. That’s the problem chimney repair in Myers Park solves, and it’s why the work starts with an inspection rather than a sales pitch. Our technicians have up to 15 years of experience reading exactly this kind of damage, from hairline crown cracks to soft, crumbling brick on older Myers Park homes where the original masonry is now well past its first repair. We handle the whole system: the firebox, the flue, the crown, the flashing and the stack. Call (833) 902-6314 and we’ll get a free estimate on the calendar. Same-day appointments are often available.
What Our Chimney Repair Service Includes
Mortar Repointing
Repointing is the work of grinding out failed mortar joints and packing in fresh mortar that bonds properly to the surrounding brick. You need it when the joints have receded, turned sandy, or started crumbling away, which lets water sit against the brick face instead of shedding off it. We match the mortar mix to the masonry so the repair doesn’t look patched and doesn’t trap moisture, and we cut the joints to the right depth rather than smearing mortar over the surface. Done correctly, repointing adds real life to a stack that’s structurally sound but weather-worn.
Spalling Brick Repair
Spalling is what happens when water soaks into a brick, freezes, and pushes the face off. The result is a flaking, pitted surface with the soft inner clay exposed, and it spreads faster than most people expect once it starts. We replace the spalled units with brick that matches the existing color and texture, then re-point around them so the new work ties into the old. Left alone, spalling eats into the structural thickness of the stack.
Chimney Waterproofing
Waterproofing is a breathable sealer applied to the exterior masonry so rain beads off while moisture inside the chimney can still escape. It’s for chimneys that are structurally sound but soaking up water, which is most of them once the mortar has aged. We apply it after any repointing or brick work is finished, because sealing over damaged masonry just locks the problem in. This is the least expensive thing on the list and the one that prevents the rest.
Flashing Repair
Flashing is the metal that seals the joint where the chimney meets the roof, and it’s the most common source of leaks we find in Myers Park. It fails when the metal pulls loose, rusts through, or was never stepped into the shingles correctly in the first place. We repair or replace the flashing and seal it against the masonry so runoff goes around the chimney instead of behind it. A leak that reads as a roof problem often turns out to be flashing.
Chimney Rebuilding
Sometimes the damage goes past what repointing and patching can fix: a crown that’s cracked through, a stack that’s leaning, or brickwork that’s lost so much material the chimney is genuinely unsafe to use. That’s when we rebuild the affected section from the roofline up, matching the original profile and materials as closely as the structure allows. We’ll tell you plainly when a rebuild is the right call and when a smaller repair will hold for years, and we back that up with camera evidence you can look at yourself.
Tuckpointing
Tuckpointing is the finer version of repointing, using a contrasting mortar to create a crisp, defined joint line on visible brickwork. Homeowners ask for it on front-facing chimneys where appearance matters alongside the structural fix. We use it when the masonry is sound enough to justify the detail work and repointing when it isn’t, so you’re not paying for cosmetics on a stack that needs structural attention first.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Brands We Service for Chimney Repair
When a repair involves relining or resurfacing, the material matters as much as the labor. We work with HeatShield, the resurfacing system that seals cracked and deteriorated flue tiles from the inside without tearing the chimney apart. For flues that need a full liner, we install DuraFlex flexible stainless liners, which can follow an offset or a misaligned flue where a rigid liner simply won’t go. Both are established names that chimney professionals specify by name, and both let us fix a flue without the demolition a lot of homeowners are bracing for.
On the masonry and component side we work with Gelco and Olympia Chimney products, from caps and crowns to the hardware that keeps a stack sealed against weather. These are trade-grade components, not the unbranded parts that fail inside a season. Whether your chimney already has Gelco or Olympia Chimney components or any other make, we can help, and we’ll tell you honestly whether what’s there can be repaired or needs replacing.
Signs You Need Chimney Repair Right Now
- Crumbling or missing mortar joints. If you can pick mortar out of the joints with a screwdriver, it’s already failed and water is getting behind it. That water freezes in a Myers Park winter and pushes the brick face apart.
- White staining on the brick. That chalky haze is efflorescence, minerals pushed to the surface by moisture moving through the masonry. It’s a reliable signal that water is getting in somewhere, even if the chimney looks fine otherwise.
- Rust or water stains inside the firebox. A damper that’s rusted shut or dark streaks running down the firebox walls mean water is coming down the flue. The cause is often a cracked crown or failed flashing rather than anything inside the chimney itself.
- A cracked or flaking crown. The crown is the concrete cap on top of the stack, and once it cracks, water runs straight into the masonry below it. A small crown repair now is far cheaper than rebuilding the top of the chimney later.
- Loose or missing flashing at the roofline. If the metal where the chimney meets the roof is pulling away or rusted through, water goes into the roof deck and framing. This is the leak most often mistaken for a roofing problem.
None of these get better on their own, and a chimney fire or a carbon monoxide problem is the outcome nobody wants to discover the hard way. A trained technician should handle the inspection and the repair; masonry work at height and anything involving the flue is not a homeowner job.
Our Chimney Repair Process – Step by Step
- 1
Inspection first, before any repair is discussed. We start with a full inspection of the firebox, flue, crown, flashing and exterior masonry. We run a camera down the flue and photograph what it finds, so you’re looking at the same evidence we are. An inspection is a standalone service: if your chimney turns out to be fine, that’s the whole visit.
- 2
We show you what we found. You get the photos and a plain explanation of what’s damaged, what’s still serviceable, and what can safely wait a season. Nothing gets recommended without camera evidence you can see for yourself.
- 3
A written estimate, flat-priced per job. You get one written price for the work, agreed before anything is scheduled. No add-ons discovered midway through the job.
- 4
The repair itself. Depending on what the inspection found, that’s repointing, brick replacement, waterproofing, flashing work, crown repair or a rebuild, using materials appropriate to the chimney. We protect the roof and surrounding surfaces while we work and clean up after.
- 5
A final check and a photo record. We verify the repair, confirm the flue is still clear, and give you photos of the finished work alongside the original problem. If anything needs watching, we tell you what to look for.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Chimney Repair Cost in Myers Park?
Chimney repair in Myers Park typically runs from a few hundred dollars for a targeted masonry fix up to several thousand for a partial rebuild, and the inspection is what tells you which end of that range you’re on. Here are the ranges we see for common work:
| Repair | Typical Estimated Range |
|---|---|
| Mortar repointing, small section | $300 – $900 |
| Tuckpointing, visible chimney face | $400 – $1,100 |
| Spalling brick replacement | $350 – $1,200 |
| Chimney waterproofing | $250 – $600 |
| Flashing repair or replacement | $300 – $800 |
| HeatShield flue resurfacing | $1,200 – $2,800 |
| DuraFlex liner installation | $1,800 – $4,500 |
| Partial chimney rebuild (above roofline) | $2,500 – $7,000 |
What moves the price is the height and access of the stack, how much masonry has to come out, and whether the flue needs resurfacing or relining on top of the exterior work. The way to avoid overpaying is to get the camera inspection first and refuse any repair that comes without evidence: a quote for a full rebuild when a repointing job would hold for another decade is the classic overcharge, and you should be able to see on camera why the bigger job is needed. Our estimates are free, and the written estimate sets the final price. Call (833) 902-6314 for an exact quote.
Chimney Repair Near Myers Park – Our Service Area
We handle chimney repair throughout Myers Park and the surrounding neighborhoods, including Elizabeth, Dilworth, Sedgefield, Cotswold, SouthPark and Plaza Midwood. We also cover chimney repair in Mint Hill and Eastover, along with NoDa, Wesley Heights, Quail Hollow and the rest of the Charlotte area. Response times depend on where you are and what’s on the schedule that day. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. When you call, we’ll give you a realistic window rather than a promise we can’t keep.
Serving Myers Park, NC – Our Local Coverage Area
We serve Myers Park and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Chimney Repair in Myers Park
Chimney repair covers any fix to the physical structure of the chimney: the mortar, brick, crown, flashing, flue lining and firebox. It’s distinct from sweeping, which removes creosote and soot, and from inspection, which is how we figure out what repair is needed. Most chimney repair jobs in Myers Park start with an inspection and end with a targeted fix rather than a full rebuild. Call (833) 902-6314 for a free estimate.
Most repairs take a day or less. Repointing, waterproofing and flashing work are typically done in a single visit, while a HeatShield resurfacing or a DuraFlex liner install usually takes one to two days depending on the flue. A partial rebuild takes longer, often several days, because mortar has to cure properly between courses. We’ll give you a realistic timeline with the written estimate so you can plan around it.
Typical chimney repair in Myers Park ranges from about $250 – $600 for waterproofing up to $2,500 – $7,000 for a partial rebuild, with most repointing and flashing jobs landing between $300 and $1,100. The final number depends on access, chimney height, and how much masonry has to be replaced. The written estimate sets the final price, and the inspection is what tells you which repair you actually need. Call (833) 902-6314 for an exact quote; estimates are free.
Yes. We work with Gelco and Olympia Chimney products and know where those components tend to wear out, from caps and crowns to the hardware that seals the stack. If your chimney already has Gelco or Olympia Chimney parts, we can assess and repair or replace them as needed. Whatever make your chimney has, we can help.
Same-day appointments are often available, depending on the schedule and the type of repair. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday, and we’re closed Saturday. A call outside dispatch hours is booked into the next opening, Sunday through Friday, 7am to 7pm. Larger jobs like a rebuild get scheduled after the inspection.
Yes. Every repair we do is backed by a satisfaction guarantee, and we stand behind the workmanship and the materials. We use trade-grade components from names like DuraFlex, HeatShield, Gelco and Olympia Chimney rather than unbranded parts, which is what makes a guarantee worth having. If something isn’t right after the repair, we’ll come back and make it right.
Clear the area around the fireplace and hearth so we have room to work, and make sure we can get to the roof access point. Move anything breakable away from the fireplace, and let us know about any pets that might get out when doors are open. If you have prior inspection reports or photos, have them ready; they help us compare what’s changed. That’s usually all the prep needed.
Schedule Your Chimney Repair Service in Myers Park Today
One specialist handles every stage of your chimney, from the free inspection through the finished repair, so you’re never coordinating between contractors. You’ll see the camera evidence before anything is recommended, and the written estimate sets the price. Call (833) 902-6314 for a no-obligation estimate. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. For routine maintenance before the burning season, our chimney sweep service is the place to start.
Written by the team at Chimney Sweep Myers Park.